Polyurethane adhesive oval gear flow meter

  Polyurethane adhesive oval gear flow meter   email: [email protected]

Shanghai JSN Micro Flow Meter CO.,LTD since we producemicro flow meter,mass flow meter,piston flow meter,electromagnetic flowmeter,oval gear flow meter,gear pump,gear metering pump,we accumulated richexperience for the flow metering equipment. The company policy is base oncontinuous research and development, which enables the company to manufacturehigh-tech and high-efficiency products. With excellent productreliability, these products are carefully selected through the carefulselection of raw materials and components, during the entire machining process,each part is carefully examined, and finally assembled with skilled experience.Before commissioning, every product has appeared in front of customers with highquality.



Polyurethane adhesive oval gear flow meter

Ovalgear flow meter  is widely used inpetroleum, chemical and hydraulic industries due to its advantages of highprecision, simple installation, stable performance and goodrepeatability.However, the Oval gear flow meter that can be produceddomestically can only be applied due to the impatience of high pressure In thelow pressure occasion, the high pressure measurement occasion can only rely onthe foreign imported high pressure flowmeter.Therefore, the research of thehigh pressure Oval gear flow meter will help to expand the domestic applicationof the Oval gear flow meter and promote the development of the domestic flowmeasurement. Deep instrumentation independent research and development of the Ovalgear flow meter pressure up to 1000bar, it can be said has reached a higherlevel in the world, and obtain measurement certificate.

TheCX-M and G-series mirco flow meters are the world"s new volumetric flowmetersintroduced by BASF in 2011. Since its establishment, the CX-M oval gear flowmeter and the G-series mirco flow meters have been selling well in the marketfor more than 100,000 units a year since they were sold. The third generationlaunched in 2017, with more than 90% accuracy and stability, won thecertification of the National Bureau of Metrology. The quality and reliabilityof Shanghai JiShen instruments need not worry. According to the statistics ofChina Instrument Association, Deep flow meter reliability has always beenranked in the top 3, especially in the long-term statistics failure rate is farbelow the industry average, deep advocate "the best after-sales service isno service", but also achieved a continuous three years without qualitycomplaints .



Polyurethane adhesive oval gear flow meter

The Ovalgear flow meter is a volumetric flow meter. The metering chamber is composed ofupper and lower end caps. The shell is formed by an oval gear rotor. The gearrotor meshes with the rotating shaft to convey the fluid. The permanent magnetarranged in the rotor is used for the detection of the rotor rotation. Twosensor holes are placed on the upper end to cover the detection sensor. Asealing ring is installed between the housing and the upper and lower end capsto prevent leakage of the measurement fluid. The base depth flowmeter is madeof a material with high wear resistance so that the flowmeter Can guaranteehigh precision measurement within the long service life.



Polyurethane adhesive oval gear flow meter

Technicaldata of CX-M Series micro oval Oval gear flow meter

Model	Flow  range	Accuracy	Connection  size
CX-M2	0.5~150ml/min	0.5%	G1/8"
CX-M3	3~300ml/min	0.5%	G1/8"
CX-M5	5~1000ml/min	0.5%	G1/8"
CX-M6	0.5~100L/H	0.5%	G1/4"
CX-M9	6~600L/H	0.5%	G1/4"
CX-M12	0.3~30L/Min	0.5%	G1/2"
CX-M25	0.5~100L/Min	0.5%	G1"

Oval gear flow meter knowledge：As a volumetric flowmeter, the tiny Oval gear flow meter has relatively low requirements for the front and rear straight pipe sections, and basically no straight pipe section requirements. The turbine flowmeter, as a speed flowmeter, has relatively high requirements for the front and rear straight pipe sections, especially for small diameter ones. Turbine flowmeter must be equipped with a corresponding section of straight pipe. Because of different internal structures, turbine flowmeters tend to generate eddy currents if they are installed too close to the bend pipe, affecting the internal impeller and affecting the accuracy of the flowmeter.